Anschluss externer Digital-Hall
Moderator: happyfreddy
-
- Beiträge: 10
- Registriert: 25. Apr 2020, 19:28
- Kontaktdaten:
Anschluss externer Digital-Hall
Hallo,
ich möchte gerne einen externen Digital-Hall
in meine Helios einschleifen.
Momentan ist ein DR-2 installiert.
Wie wäre die Anschluß-Belegung in Verbindung mit VV3?
Grüße Didi
ich möchte gerne einen externen Digital-Hall
in meine Helios einschleifen.
Momentan ist ein DR-2 installiert.
Wie wäre die Anschluß-Belegung in Verbindung mit VV3?
Grüße Didi
-
- Beiträge: 2347
- Registriert: 19. Jul 2012, 09:32
- Kontaktdaten:
Re: Anschluss externer Digital-Hall
Von einer der beiden VV Steckkarten ( die mit den Hallverstärkern ) gehen die Zuleitungen zum Feder
oder Digihall ab ( abgeschirmte Leitungen ) auf die dortigen Cinch Stecker.
Diese Leitungen einfach auf entsprechende Cinch Ausgangsbuchsen verlängern.
Ab da dann passende Steckverbindungen zum Ein und Ausgang des externen Hallgerätes.
Den DR 2 komplett abziehen und die Änderungen für die beiden Hallschalter Hall 1 und Hall 2 wieder
auf Version vor Einbau DR 2 zurückbauen - also für Hallspirale.
oder Digihall ab ( abgeschirmte Leitungen ) auf die dortigen Cinch Stecker.
Diese Leitungen einfach auf entsprechende Cinch Ausgangsbuchsen verlängern.
Ab da dann passende Steckverbindungen zum Ein und Ausgang des externen Hallgerätes.
Den DR 2 komplett abziehen und die Änderungen für die beiden Hallschalter Hall 1 und Hall 2 wieder
auf Version vor Einbau DR 2 zurückbauen - also für Hallspirale.
-
- Beiträge: 10
- Registriert: 25. Apr 2020, 19:28
- Kontaktdaten:
Re: Anschluss externer Digital-Hall
Noch viel mehr Danke.
-
- Beiträge: 26
- Registriert: 11. Sep 2019, 20:02
- Kontaktdaten:
Re: Anschluss externer Digital-Hall
is it possible to get reverb return in stereo with example alesis verb?
-
- Beiträge: 2347
- Registriert: 19. Jul 2012, 09:32
- Kontaktdaten:
Re: Anschluss externer Digital-Hall
The preamp mainboard VV 2 has two plugged in VV 1 or VV 3 boards.
Mainboard is only the switching section and the VV 2 or Vv 3 the real preamp boards
Normal only one preamp board has the driver and return of reverb coil or digital reverb.
Between the two preamp board there are two cable connection at pins RA and RE.
These cables mixe the two channel signals R and L to the reverb driver input and
send the reverb signal to the both channels .
If You want to separate the channels for a Alesis Reverb just disconnect the cables
located at pins RA and RE. The second Preamp VV 1 or VV 3 must be modified with the
driver IC 1 and C1 and R 1 , R 4 so that at pin F1 of this preamp You have the signal for
second channel for the Alesis reverb.
The VV 1 or VV 3 preamp with buildt in complete Reverb parts in old configuration You also
must modifiy a little. Disconnect two condenser C 14 and C 5 on this preamp and solder a wire
from Pin F 2 direct to Pin RA of this preamp.
Finally You have now two identy preamps and the plug F 1 is on bothe preamps the Output
for a Alesis reverb . The plug F 2 is the new Input for the reverb signal from Alesis.
Please regard the shield of conneting cable. Ground only at F1 connection never the return
from Alesis caused hum.
Mainboard is only the switching section and the VV 2 or Vv 3 the real preamp boards
Normal only one preamp board has the driver and return of reverb coil or digital reverb.
Between the two preamp board there are two cable connection at pins RA and RE.
These cables mixe the two channel signals R and L to the reverb driver input and
send the reverb signal to the both channels .
If You want to separate the channels for a Alesis Reverb just disconnect the cables
located at pins RA and RE. The second Preamp VV 1 or VV 3 must be modified with the
driver IC 1 and C1 and R 1 , R 4 so that at pin F1 of this preamp You have the signal for
second channel for the Alesis reverb.
The VV 1 or VV 3 preamp with buildt in complete Reverb parts in old configuration You also
must modifiy a little. Disconnect two condenser C 14 and C 5 on this preamp and solder a wire
from Pin F 2 direct to Pin RA of this preamp.
Finally You have now two identy preamps and the plug F 1 is on bothe preamps the Output
for a Alesis reverb . The plug F 2 is the new Input for the reverb signal from Alesis.
Please regard the shield of conneting cable. Ground only at F1 connection never the return
from Alesis caused hum.
-
- Beiträge: 177
- Registriert: 21. Mai 2019, 14:42
- Kontaktdaten:
Re: Anschluss externer Digital-Hall
...vielleicht helfen die paar Anleitungen:
-
- Beiträge: 2347
- Registriert: 19. Jul 2012, 09:32
- Kontaktdaten:
Re: Anschluss externer Digital-Hall
Aus der BA 3317 geht ua die Bestückung und Zuordnung des DH 11 für die verschiedenen
Orgelmodelle bezüglich der Taster für Hallprogramme etc hervor.
Orgelmodelle bezüglich der Taster für Hallprogramme etc hervor.
-
- Beiträge: 26
- Registriert: 11. Sep 2019, 20:02
- Kontaktdaten:
Re: Anschluss externer Digital-Hall
Someone who has schematic on VV3?
-
- Beiträge: 107
- Registriert: 10. Aug 2013, 15:32
- Wohnort: Schwaikheim (ca. 20 km nordöstlich von Stuttgart)
- Kontaktdaten:
Re: Anschluss externer Digital-Hall
They are in BA 560 (Vorstufe VV2 + VV3) and BA 570 (Hall-Set mit VV3).
Greetings
Martin
Wer ist online?
Mitglieder in diesem Forum: 0 Mitglieder und 0 Gäste