HOAX3 FAQ

Rund um die "Clonewheels" HX3.1 bis HX3.4 (mk4) und HOAX 2

Moderator: happyfreddy

bovist
Site Admin
Beiträge: 475
Registriert: 6. Jul 2012, 14:28
Kontaktdaten:

HOAX3 FAQ

Beitrag von bovist »

Wenn Sie Fragen, Anregungen und Tipps zum HOX-Modul haben... Hier werden Sie geholfen!

-cm
Kermit
Beiträge: 9
Registriert: 21. Jul 2012, 15:16
Wohnort: Denmark
Kontaktdaten:

Re: HOAX3 FAQ

Beitrag von Kermit »

Hi,

Well, while I waiting for my HOAX to arrive, I´m in the process of planning :D
Have you made the drawbar inputs logaritmic or should it be a logaritmic poti ?
I know that the resistor values was original logaritmic - but if you did make that correction in the firmware, it would be a little strange result if I use log values :)

Best regards

Claus
bovist
Site Admin
Beiträge: 475
Registriert: 6. Jul 2012, 14:28
Kontaktdaten:

Re: HOAX3 FAQ

Beitrag von bovist »

Hi Claus,

log pots should work, although hammond db characteristic is only "somewhat" log. There is no lin-log conversion in the firmware. You may use lin pots with a "ballast" resistor to ground on output, which also yields a "somewhat" log characteristic. E.g. 3k3 on a 10k pot.
Tommy
Beiträge: 5
Registriert: 26. Jul 2012, 16:30
Kontaktdaten:

Re: HOAX3 FAQ

Beitrag von Tommy »

Hallo,
habe eine Frage zu meiner neuen HOAX-Platine: Diese ist vorkonfiguriert für die OrganScan61-Platine(n). Laut Beschreibung im Wiki sollte der MIDI-Eingang unabhängig davon funktionieren, darüber wollte ich natürlich die HOAX schon einmal probespielen. Die Controller lassen sich auch ansteuern (Leslie, Volume, Drawbars etc.), wie an den Nebengeräuschen bzw. der LED zu hören und sehen ist. Leider nimmt die Platine aber keine Tastaturbefehle entgegen. Woran kann das liegen?

Gruß Tommy
Tommy
Beiträge: 5
Registriert: 26. Jul 2012, 16:30
Kontaktdaten:

Re: HOAX3 FAQ

Beitrag von Tommy »

Hi, Lesen hilft tatsächlich ;) Nach Anstecken der Scanplatine ist alles bestens!

Tommy
bovist
Site Admin
Beiträge: 475
Registriert: 6. Jul 2012, 14:28
Kontaktdaten:

Re: HOAX3 FAQ

Beitrag von bovist »

Man kann den OrganScan61-HOAX auch ohne Scan-Platinen betreiben, wenn man von PL14 Pin 5 eine Verbindung zu PL14 Pin10 legt.
Paul
Beiträge: 1
Registriert: 30. Jul 2012, 12:34
Kontaktdaten:

Re: HOAX3 FAQ

Beitrag von Paul »

Hallo,

was würde ich sonst noch benötigen, um die HOAX-Platine in eine defekte Hammond XB-2 einzubauen?
Eventuell Scanner-Platine usw.?

Viele Grüße

Paul
bovist
Site Admin
Beiträge: 475
Registriert: 6. Jul 2012, 14:28
Kontaktdaten:

Re: HOAX3 FAQ

Beitrag von bovist »

Paul hat geschrieben:was würde ich sonst noch benötigen, um die HOAX-Platine in eine defekte Hammond XB-2 einzubauen?
Eventuell Scanner-Platine usw.?l
Hallo Paul,

meist funktioniert in defekten XB2 der MIDI-Ausgang noch, so dass Sie keine Scan-Platine benötigen (MIDI-only-Version). Die Zugriegel müssen allerdings an HOAX angeschlossen werden. Sie können als Bedienpanel das Panel16 benutzen, das vor den Zugriegeln anstelle der Pitchwheels installiert wird (siehe Video http://youtu.be/vvBlFP_0AMw). Lassen Sie die Pitchwheel-Potis aber angeschlossen.
ratpackryan
Beiträge: 28
Registriert: 5. Aug 2012, 00:44
Kontaktdaten:

Re: HOAX3 FAQ

Beitrag von ratpackryan »

I was wondering if a Korg expression pedal will work? Everything is the same as the Yamaha except the Korg goes from about 0.3 kilohms to 54 kilohms. Is this enough to make a difference? What adverse effects will this have? I can adjust the swing of the pedal so that it reaches the maximum at 47 kilohms but I cannot adjust the minimum.
Thanks in advance
bovist
Site Admin
Beiträge: 475
Registriert: 6. Jul 2012, 14:28
Kontaktdaten:

Re: HOAX3 FAQ

Beitrag von bovist »

ratpackryan hat geschrieben:I was wondering if a Korg expression pedal will work? Everything is the same as the Yamaha except the Korg goes from about 0.3 kilohms to 54 kilohms. Is this enough to make a difference?

If you measure those 0.3 kilohms to 54 kilohms from plug tip to shaft and around 50 kOhms from plug ring to shaft, it should work well. Absolute values are not critical. If the expression pedal's plug has no ring, it will not work.
Antworten

Wer ist online?

Mitglieder in diesem Forum: 0 Mitglieder und 35 Gäste