HX3.5 Firmware 5.533 BETA

Erfahrungen und allgemeine Fragen zum HX3.5-Board und zum HX3.5 Editor

Moderator: happyfreddy

bovist
Site Admin
Beiträge: 463
Registriert: 6. Jul 2012, 14:28
Kontaktdaten:

HX3.5 Firmware 5.533 BETA

Beitrag von bovist »

Firmware #5.533 introduces named presets for MenuPanel and HX3.5 Panel, as well as the HX3.5 Preset Mover for easy copying and assembling preset setups with "Preset Preview" function (try out entries in saved "preset.dat" files). New "Snapshot" allows direct transfer of current organ setup to a Preset file entry without saving it to HX3.5 itself.

Please see HX3.5 Panel user manual in BETA directory. We removed obsolete HX3.5 Configurator as it is completely covered by new HX3.5 Editor. Preset Mover's "Preview", "Snapshot" and "Edit" functions will only work with firmware #5.533 and up.

07.02.2020 Firmware #5.533, FPGA 17012020, HX3.5 Editor 5.532

* Firmware: Some adjustments to Mojo/Hamichord MIDI CC set (Equalizer control). Note: As Mojo sends a CC on "Bank Select LSB" (32), set Preset CC in menu to an unused MIDI controller (ie. 126 or 127).
* Firmware: Added support for named Presets (needs new "Preset Mover" to rename)
* Firmware: Added support for "Preset Preview" and "Snapshot" function
* FPGA: Adjusted V1/V2/V3 volume, somewhat higher
* Update script: Adjust Chorus Dry Level (now default 90) to compensate for higher delay line (wet) output
* New Preset Mover available in HX3.5 Editor and HX3.5 Panel

Some improvements of HX3.5 firmware are due as some customers complained about the too-low Percussion Drawbar level in EG PERC mode (electronic gating) and incompatibilities of MIDI bank select command for Common Preset recall.
Find it here: http://keyboardpartner.remotewebaccess. ... 20Firmware

03.01.2020 Firmware #5.527, FPGA 03012020

* Firmware, Feature: Arbitrary MIDI CC selection parameter for "Common Preset" change (also available in MIDI menu), default #32 (Bank Select LSB), valid in all MIDI CC sets
* Firmware, Feature: High Foldback Mode (M100 OFF, B3 ON) in menu
* Firmware, Improvement: Deeper modulation factors for CaM rotary sim and Phasing Rotor
* Firmware, Feature: Preset Save/Restore Mask #1498 (System Inits) changed to 127 (all bits ON = all saved/restored) on Expander models
* Firmware, Feature: Percussion Drawbars in Electronic Gating Perc mode automatically enabled
* Firmware, Bugfix: Indication of Default or Common Preset Save in menu now according to "Preset Save/Restore Mask" parameter #1498 (System Inits)
* FPGA: Lower AO28 Preamp noise
* FPGA: Higher Percussion Drawbars level in EG Perc mode
* HX3.5 Configurator/Editor: Small improvements, will show destination of saved parameter (Default or Preset) according to "Preset Save/Restore Mask" parameter #1498 (System Inits)
* HX3.5 Configurator/Editor: Some lines from #6200 up had wrong max. values
* HX3.5 Editor (same as Configurator, but with Tab Panel) added for experienced users
Gruß, Carsten aka bovist
----------------------------------------------------
Manchmal weiß ich einfach nicht, wie ich einen Satz beenden

Philicorda AG7500
Bontempi PM68
Farfisa Jaqueline Deluxe
Schellenring 30cm
emmanuel bex

Re: HX3.5 Firmware 5.533 BETA

Beitrag von emmanuel bex »

Hello. I just updated to the version that works with OSC touch. But it doesn't work. I have a new ipad I integrated the layouts in itunes .. When I arrive on the page of the app where you have to connect, it does not work. My firmware: 5.537 Scan 54.24 and DSP 01.19. It is very difficult for me to follow the video tutorials in German, that is why I leave this message in English. Do you have an idea?
I do not have a lightning cable usb b, so I use a usb changer B to usb C. Maybe the problem comes from there.
Thank you and congratulations for everything!
m_g
Beiträge: 248
Registriert: 25. Sep 2013, 16:48
Kontaktdaten:

Re: HX3.5 Firmware 5.533 BETA

Beitrag von m_g »

Hi,

maybe you should try the actual current firmware (found in the "current firmware" folder in guithub)
5.607 (11.5.2020) !

It seems there are many issues and bugs fixed since 5.537
----------------------------------------------
Live: UHL X4-V2, Yamaha CP88, MS KP500S, Leslie 760mod
Studio: Hammond XK5+XLK5+Vent1, HX3.5, Prophet 6, Yamaha Montage 7, Yamaha P515, Roland SE02
Christian
Beiträge: 106
Registriert: 14. Nov 2015, 13:46
Kontaktdaten:

Re: HX3.5 Firmware 5.533 BETA

Beitrag von Christian »

Emmanuel, you've already got answers when you brought this up first time:

viewtopic.php?f=8&t=945&start=20#p6382
Antworten

Wer ist online?

Mitglieder in diesem Forum: 0 Mitglieder und 2 Gäste