Seite 1 von 10

HOAX3 FAQ

Verfasst: 19. Jul 2012, 08:42
von bovist
Wenn Sie Fragen, Anregungen und Tipps zum HOX-Modul haben... Hier werden Sie geholfen!

-cm

Re: HOAX3 FAQ

Verfasst: 21. Jul 2012, 15:31
von Kermit
Hi,

Well, while I waiting for my HOAX to arrive, I´m in the process of planning :D
Have you made the drawbar inputs logaritmic or should it be a logaritmic poti ?
I know that the resistor values was original logaritmic - but if you did make that correction in the firmware, it would be a little strange result if I use log values :)

Best regards

Claus

Re: HOAX3 FAQ

Verfasst: 23. Jul 2012, 20:20
von bovist
Hi Claus,

log pots should work, although hammond db characteristic is only "somewhat" log. There is no lin-log conversion in the firmware. You may use lin pots with a "ballast" resistor to ground on output, which also yields a "somewhat" log characteristic. E.g. 3k3 on a 10k pot.

Re: HOAX3 FAQ

Verfasst: 26. Jul 2012, 16:40
von Tommy
Hallo,
habe eine Frage zu meiner neuen HOAX-Platine: Diese ist vorkonfiguriert für die OrganScan61-Platine(n). Laut Beschreibung im Wiki sollte der MIDI-Eingang unabhängig davon funktionieren, darüber wollte ich natürlich die HOAX schon einmal probespielen. Die Controller lassen sich auch ansteuern (Leslie, Volume, Drawbars etc.), wie an den Nebengeräuschen bzw. der LED zu hören und sehen ist. Leider nimmt die Platine aber keine Tastaturbefehle entgegen. Woran kann das liegen?

Gruß Tommy

Re: HOAX3 FAQ

Verfasst: 26. Jul 2012, 16:50
von Tommy
Hi, Lesen hilft tatsächlich ;) Nach Anstecken der Scanplatine ist alles bestens!

Tommy

Re: HOAX3 FAQ

Verfasst: 26. Jul 2012, 18:32
von bovist
Man kann den OrganScan61-HOAX auch ohne Scan-Platinen betreiben, wenn man von PL14 Pin 5 eine Verbindung zu PL14 Pin10 legt.

Re: HOAX3 FAQ

Verfasst: 30. Jul 2012, 12:39
von Paul
Hallo,

was würde ich sonst noch benötigen, um die HOAX-Platine in eine defekte Hammond XB-2 einzubauen?
Eventuell Scanner-Platine usw.?

Viele Grüße

Paul

Re: HOAX3 FAQ

Verfasst: 31. Jul 2012, 15:10
von bovist
Paul hat geschrieben:was würde ich sonst noch benötigen, um die HOAX-Platine in eine defekte Hammond XB-2 einzubauen?
Eventuell Scanner-Platine usw.?l
Hallo Paul,

meist funktioniert in defekten XB2 der MIDI-Ausgang noch, so dass Sie keine Scan-Platine benötigen (MIDI-only-Version). Die Zugriegel müssen allerdings an HOAX angeschlossen werden. Sie können als Bedienpanel das Panel16 benutzen, das vor den Zugriegeln anstelle der Pitchwheels installiert wird (siehe Video http://youtu.be/vvBlFP_0AMw). Lassen Sie die Pitchwheel-Potis aber angeschlossen.

Re: HOAX3 FAQ

Verfasst: 5. Aug 2012, 00:53
von ratpackryan
I was wondering if a Korg expression pedal will work? Everything is the same as the Yamaha except the Korg goes from about 0.3 kilohms to 54 kilohms. Is this enough to make a difference? What adverse effects will this have? I can adjust the swing of the pedal so that it reaches the maximum at 47 kilohms but I cannot adjust the minimum.
Thanks in advance

Re: HOAX3 FAQ

Verfasst: 5. Aug 2012, 09:23
von bovist
ratpackryan hat geschrieben:I was wondering if a Korg expression pedal will work? Everything is the same as the Yamaha except the Korg goes from about 0.3 kilohms to 54 kilohms. Is this enough to make a difference?

If you measure those 0.3 kilohms to 54 kilohms from plug tip to shaft and around 50 kOhms from plug ring to shaft, it should work well. Absolute values are not critical. If the expression pedal's plug has no ring, it will not work.