Firmware #3.83
Moderator: happyfreddy
-
- Site Admin
Re: Firmware #3.83
.....Tone trim Pot.... bei Version 3.83 mk3 - bewegt sich nur zwischen 95 und 100 - gespeichert wird immer der Wert 100. Auch mit der remote Software vorgenommene Änderungen werden an meinem Expander nur mit dem Wert 100 gespeichert. Bug? :o
-
- Site Admin
Re: Firmware #3.83
...problem hat sich durch dektivieren des Haken erledigt...jetzt geht wieder alles..
-
- Beiträge: 9
- Registriert: 1. Aug 2014, 12:17
- Kontaktdaten:
Re: Firmware #3.83
Hi all,
I have Expander mk3 updated to 3.83c (latest FPGA, Firmware, ScanCore).
Now there are obvious crackle in some cases, seems to be a sort of internal "overload" or processing overflow.
Best replicated on louder/extreme settings, i.e.:
TG "Recapped" / All drawbars out / Press several notes in highest octave simultaneously.
I can face it even on 888/Recapped while holding 5 highest white keys.
'72 caps requires a bit more notes or active drawbars.
Double-checked with:
- different commutation schemes;
- direct, plain organ signal (no internal Leslie model or pedals);
- default settings (except TG caps).
Have anybody faced the same issue or could reproduce it?
I have Expander mk3 updated to 3.83c (latest FPGA, Firmware, ScanCore).
Now there are obvious crackle in some cases, seems to be a sort of internal "overload" or processing overflow.
Best replicated on louder/extreme settings, i.e.:
TG "Recapped" / All drawbars out / Press several notes in highest octave simultaneously.
I can face it even on 888/Recapped while holding 5 highest white keys.
'72 caps requires a bit more notes or active drawbars.
Double-checked with:
- different commutation schemes;
- direct, plain organ signal (no internal Leslie model or pedals);
- default settings (except TG caps).
Have anybody faced the same issue or could reproduce it?
-
- Beiträge: 248
- Registriert: 25. Sep 2013, 16:48
- Kontaktdaten:
Re: Firmware #3.83
Yes, known issue. I thought it is fixed in the actual version???
If you are not afraid in using the tapering tool and remote software you can fix it.
Reduce the Tonewheel 77 (5/14 drawbar) in the tapering tool on all 4 sets (you can check it by ear on the highest A).
Put the gain to 0.9 or less in the tapering tool.
In the remote reduce the parameter 609 (leslie input level) down till the clipping dissapears
(should be somewhere between 135 to 110).
Maybe Carsten can chime in here ?!
If you are not afraid in using the tapering tool and remote software you can fix it.
Reduce the Tonewheel 77 (5/14 drawbar) in the tapering tool on all 4 sets (you can check it by ear on the highest A).
Put the gain to 0.9 or less in the tapering tool.
In the remote reduce the parameter 609 (leslie input level) down till the clipping dissapears
(should be somewhere between 135 to 110).
Maybe Carsten can chime in here ?!
-
- Beiträge: 9
- Registriert: 1. Aug 2014, 12:17
- Kontaktdaten:
Re: Firmware #3.83
Thank you, maybe I will try it later.
Until that returned to default '61 caps.
Until that returned to default '61 caps.
-
- Beiträge: 118
- Registriert: 14. Apr 2015, 19:48
- Kontaktdaten:
Re: Firmware #3.83
Hi guys !
There is a new update since yesterday, should be done now thought
Regards !
There is a new update since yesterday, should be done now thought
Regards !
-
- Beiträge: 248
- Registriert: 25. Sep 2013, 16:48
- Kontaktdaten:
Re: Firmware #3.83
Nice, thanks Ramon for the heads up!!!
There should be an email newsletter for users,
can't follow all the changes in the latest folder...and often miss the very latest!
;-)
There should be an email newsletter for users,
can't follow all the changes in the latest folder...and often miss the very latest!
;-)
-
- Beiträge: 149
- Registriert: 21. Jul 2014, 15:37
- Kontaktdaten:
Re: Firmware #3.83
With my new FTDI board sent very quickly by Carsten I now have the latest update successfully installed. The chorus/vibrato seems to be improved - is this connected with the tapering changes?
I had a problem with this latest try at the update using Windows 10, and the HX3 became corrupted. I thought using AV_Repair would quickly fix this but I couldn't get it to work properly with Windows 10. Going back to WindowsXP solved the problem with AV_Repair, and after I installed the latest #383 update everything worked fine from Windows 10. Maybe the AV_repair tool now needs updating?
It all sounds excellent - I'm running out of things to ask for :-)
Paul
I had a problem with this latest try at the update using Windows 10, and the HX3 became corrupted. I thought using AV_Repair would quickly fix this but I couldn't get it to work properly with Windows 10. Going back to WindowsXP solved the problem with AV_Repair, and after I installed the latest #383 update everything worked fine from Windows 10. Maybe the AV_repair tool now needs updating?
It all sounds excellent - I'm running out of things to ask for :-)
Paul
-
- Beiträge: 248
- Registriert: 25. Sep 2013, 16:48
- Kontaktdaten:
Re: Firmware #3.83
....so very very latest update installed....everything PERFECT now !
As Paul said: what to ask for now ???
;-))
As Paul said: what to ask for now ???
;-))
-
- Beiträge: 118
- Registriert: 14. Apr 2015, 19:48
- Kontaktdaten:
Re: Firmware #3.83
Hi guys !
Also my HX3 is perfect !
Also my HX3 is perfect !
maybe the last candy on the top : transposition via midi from XK3 system... (thoughts) ;)m_g hat geschrieben:....so very very latest update installed....everything PERFECT now !
As Paul said: what to ask for now ???
;-))
Wer ist online?
Mitglieder in diesem Forum: Bing [Bot] und 106 Gäste