output conf on extension board

Antwort erstellen


Diese Frage dient dazu, das automatisierte Versenden von Formularen durch Spam-Bots zu verhindern.
Smilies
:D :) ;) :( :o :shock: :? 8-) :lol: :x :P :oops: :cry: :evil: :twisted: :roll: :!: :?: :idea: :arrow: :| :mrgreen: :geek: :ugeek:

BBCode ist eingeschaltet
[img] ist eingeschaltet
[flash] ist ausgeschaltet
[url] ist eingeschaltet
Smilies sind eingeschaltet

Die letzten Beiträge des Themas
   

Ansicht erweitern Die letzten Beiträge des Themas: output conf on extension board

Re: output conf on extension board

von billyb » 17. Okt 2020, 04:58

to clarify - by aux 1 , i mean PL39 on the extension board ( the left jack ) , just realized what i had written , sorry for the confusion .

Re: output conf on extension board

von billyb » 13. Okt 2020, 22:06

for my setup i'm only using audio ( pins 1 & 4 ) from the ext. board , pins 6,7 ,8 on 11 pin go directly to my leslie switch ( 5 is jumpered
with a switch to 6 ) , it's to power a 3300 . i use a leslie 11 to 6 pin adapter box for the 122 . the box was modified to be able
to trigger a brake function in the leslie . i use this setup so i can use the other pole in the switch to operate a vent . so , i could
use 2 good dry outputs , one for aux 1 and one for the 11 pin . one conf setting sounds great on the 11 pin , the other is good for the aux output .
haven't run through my 3300 , it's not home

Re: output conf on extension board

von happyfreddy » 13. Okt 2020, 20:17

I hope You know that a 122 Leslie needs a symmetric input audio signal ? !
The output from the extensionboard or direct from HX 3 board is still assymmetric.

How did You convert the fast -slow command voltage from Extension board ?
A 122 Leslie realizes this with a 100 V DC voltage added to the symmetric audio signal.

Re: output conf on extension board

von billyb » 13. Okt 2020, 19:12

by PCB , you mean which hx3 ? i have HX3-MK4 ser # 6403709 ,4.25 with the latching hex. firmware ,
i have the extension board , i believe it's the older type , all switching is in proper working order ,
2 drawbar sets per manual , toggle switches for vib. on /off each manual and also 4 for perc. and 2 reverb .
vib. knob and 2 pots

Re: output conf on extension board

von bovist » 13. Okt 2020, 15:10

Hello,

which PCB version are you using?

Re: output conf on extension board

von billyb » 13. Okt 2020, 13:13

if i may add to my post , hooked up the hx3 to my 122 last night , the AMP/PD L/R +B output is definitely
the stronger output for the 11 pin , sounds much fuller , but for some reason this doesn't work that well
for AUX 1 on the extension board .

output conf on extension board

von billyb » 12. Okt 2020, 16:05

yes hello , have finally completed remote settings for my build , am just using 2 outputs , both from the extension board .
the left 1/4 " jack and the 11 pin .the l/r amp/pd+b is ideal for the jack ( for vent input ) but not so much for the
11 pin ( output is not as strong , compared on phones , not as full ) amp/pd l/r+b is ideal for this ,but not for the 1/4" , sounds
weak . is there a way to equalize these outputs ? there are situations where i would be using both . my double pole leslie
switch keeps them both in sync . the vent goes directly to the house , the leslie is my stage monitor .

Nach oben